Effects of Synthesis Conditions on the Formation of Si-Substituted Alpha Tricalcium Phosphates

Powders of α-TCP containing various amounts of silicon were synthesized by two different methods: Wet chemical precipitation and solid-state synthesis. The obtained powders were then physico–chemically studied using different methods: Scanning and transmission electron microscopy (TEM and SEM), energy-dispersive X-ray spectroscopy (EDS), powder X-ray diffractometry (PXRD), infrared and Raman spectroscopies (FT-IR and R), and solid-state nuclear magnetic resonance (ssNMR). The study showed that the method of synthesis affects the morphology of the obtained particles, the homogeneity of crystalline phase and the efficiency of Si substitution. Solid-state synthesis leads to particles with a low tendency to agglomerate compared to the precipitation method. However, the powders obtained by the solid-state method are less homogeneous and contain a significant amount of other crystalline phase, silicocarnotite (up to 7.33%). Moreover, the microcrystals from this method are more disordered. This might be caused by more efficient substitution of silicate ions: The silicon content of the samples obtained by the solid-state method is almost equal to the nominal values.     

The effect of traffic data source on deterioration rates of heavy-duty flexible pavements

The purpose of this study is to assess the effect of traffic data source (estimated vs. actual) on predicted progression rates of roughness and rutting for heavy-duty flexible pavements of rural freeways. Progression rates are predicted using calibrated HDM-4 models. The assessment is performed in terms of variations in maintenance intervention timing associated with the variations in progression rates. Time series pavement condition data (covering 3–5 years) have been collected for 7 sections of rural freeways for use in calibrating HDM-4 deterioration models. They range in length from 10 to 60.8 km and cover different traffic volumes, climate zones and subgrade soil types. For these sections, estimated annual average daily traffic (AADT), growth factors and assumed loading have been extracted from relevant database. Only six segments of these sections have Weigh-in-Motion (WIM) sites so relevant actual AADT, growth factors and axle load distributions have been extracted from WIM reports. The results of running the calibrated HDM-4 deterioration models using different traffic data show that actual traffic data from WIM sites result in higher rates of deterioration to that of estimated data for four sites, resulting in earlier intervention timing and higher present value agency cost. The other two sites have lower rates with actual data due to lower traffic loading than estimated.     

双盘式磁力耦合器振动噪声分析与实验研究

为了在双盘式磁力耦合器设计阶段分析振动噪声特性,优化双盘式磁力耦合器设计,提出了一种利用模态叠加原理来分析其振动噪声的方法。双盘式磁力耦合器具有高转矩密度与高效率等优势,因此逐渐发展成为煤矿机械柔性传动装置。由于双盘式磁力耦合内部的转子磁场非正弦分布以及涡电流谐波等因素影响,双盘式磁力耦合器输出转矩中不可避免的存在波动。若根据计算得出的双盘式磁力耦合器的电磁振动噪声特点,在设计时选取振动噪声小的参数进行优化组合,可在实际中降低其电磁振动及噪声,有利于减少制造成本。本文结合双盘式磁力耦合器的结构特征,提出了一种模态叠加响应法计算电磁振动噪声,建立了其电磁径向力的解析模型,并在多物理场耦合作用下分析主要电磁径向力波在工作频率内的谐波响应,最后在额定功率为55 kW双盘式磁力耦合器实验台上进行试验验证。基于麦克斯韦张量法,建立了双盘式磁力耦合器的径向电磁力解析模型,并得出0阶与10阶电磁径向力波是产生振动噪声的最主要原因;利用多物理场耦合分析法进行谐波响应NVH特性分析,结果显示0阶力波的振动加速度与形变量均大于10阶力波的振动加速度与形变量,因此双盘式磁力耦合器的电磁振动主要来源于0阶力波;在额定功率为55 kW,最高转速为1 500 r/min的双盘式磁力耦合器实验台进行振动测试,试验结果显示在1 500 r/min时,试验得出的最大振动峰值及频率约为35 m/s^2和4 950 Hz,与有限元仿真结果的误差对应为6.3%和1.1%;而当变频电机的输入转速依次增大时,振动加速度的理论值、仿真值与试验值的曲线形态较为接近,误差较小;噪声估计值与实测值的最大误差仅为8.9%,基本验证了本文所提出模态叠加法的正确性。     

Study of physicochemical properties of flutamide-loaded Ocimum basilicum microspheres with ex vivo mucoadhesion and in vitro drug release

Drug which shows extensive first pass effect is difficult task that, needs to be solved by formulators in the pharmaceutical science. The low oral bioavailability (49%) of flutamide may be due to poor wettability, low aqueous solubility and extensive first pass effect. The aim of present investigation was to prepare flutamide loaded microspheres and incorporate it into suppositories for rectal delivery to avoid first pass effect and enhance residence time. Flutamide loaded mucoadhesive microspheres of Ocimum Basilicum mucilage (OBM) were prepared using spray drying and characterized by percent production yield, encapsulation efficiency, particle size, zeta potential, polydispersity index, DSC, SEM, XRPD, in vitro drug release and stability studies. Moreover, ex vivo mucoadhesion was investigated using falling liquid film technique to determine the adhesion of microspheres to sheep rectal mucosa. The microspheres had nearly spherical shape and size about 2.53?μm. The encapsulation efficiency and mucoadhesion of optimized formulation MBF10 were found to be 69.6?±?2.3% and 89.01?±?2.18%, respectively. Percent CDR of optimized flutamide loaded mucoadhesive microspheres was found to be 88.7?±?1.3 at 7?h. In conclusion, OBM microparticles based suppository could be used to deliver drug through rectal delivery.     

The control of paracetamol particle size and surface morphology through crystallisation in a spray dryer

The parameters governing the crystallisation of paracetamol using various conventional techniques has been extensively studied, however the factors influencing the drug crystallisation using spray drying is not as well understood. The aim of this work was to investigate the crystallisation of an active pharmaceutical ingredient through evaporative crystallisation using a spray dryer to study the physicochemical properties of the drug and to use semi-empirical equations to gain insight into the morphology and particle size of the dried powder. Paracetamol solutions were spray dried at various inlet temperatures ranging from 60 °C to 120 °C and also from a series of inlet feed solvent compositions ranging from 50/50% v/v ethanol/water to 100% ethanol and solid-state characterisation was done. The size and morphology of the dried materials were altered with a change in spray drying parameters, with an increase in inlet temperature leading to an increase in particle Sauter mean diameter (from 3.0 to 4.4 µm) and a decrease in the particle size with an increase in ethanol concentration in the feed (from 4.6 to 4.4 µm) as a result of changes in particle density and atomised droplet size. The morphology of the dried particles consisted of agglomerates of individual crystallites bound together into larger semi-spherical agglomerates with a higher tendency for particles having crystalline ridges to form at higher ethanol concentrations of the feed.     

Lewis acid-oxygen vacancy interfacial synergistic catalysis over SO42−/Ce0.84Zr0.16O2–WO3–ZrO2 for N,N-diethylation of aniline with ethanol

Herein, a new mechanism involving Lewis acid-oxygen vacancy interfacial synergistic catalysis for aniline N,N-diethylation with ethanol was proposed, and the SO₄²⁻/Ce_0.84Zr_0.16O₂–WO₃–ZrO₂ catalyst (SCWZ) with both Lewis acid sites and oxygen vacancies was synthesized by the hydrothermal method, which shows better catalytic activity than the reported solid acidic catalysts. Besides, the SO₄²⁻/ZrO₂ (SZ) and SO₄²⁻/WO₃–ZrO₂ (SWZ) catalysts were also prepared and compared with SCWZ to investigate the synergistic effect of each component. The SO₄²⁻ and WO₃ mainly generate Lewis acid by bonding with ZrO₂, which is beneficial for the fracture of the N–H bond in aniline. The Ce_0.84Zr_0.16O₂ solid solution mainly plays a vital role in generating the oxygen vacancies as the interface active species, which can participate in stripping –OH from ethanol, then the carbocation will also be released, which only needs 1.3805 kcal/mol energy, calculated by density functional theory (DFT), to be input. In comparison, the traditional reaction mechanism needs the Brønsted acidic sites to promote the protonation of ethanol, then dehydration and subsequent formation of carbocation followed, and 108.6846 kcal/mol energy needs to be input, which is far higher than that of the new mechanism. The apparent activation energy (E_a) over SCWZ was measured by experiment to be 34.09 kJ/mol, which is much lower than that of SWZ (47.10 kJ/mol) and SZ (54.37 kJ/mol), illustrating comparatively preferable kinetics for SCWZ than that of SWZ and SZ. Besides, the conversion of aniline and selectivity to N,N-diethylaniline over SCWZ reach almost 100% and 73%, respectively. The SCWZ can be renewed for 4 times without rapid deactivation, and the longevity of SCWZ is longer than that of SWZ and SZ, as the loaded SO₄²⁻ and tetragonal ZrO₂ are stabilized by Ce_0.84Zr_0.16O₂ and WO₃, respectively.     

GeTe中铁电极化对自旋霍尔电导的调控研究

利用电场控制电荷的自旋流与电流相互转换是自旋电子器件的关键所在,而这种控制机制在铁电半导体GeTe中可以得到实现,因为其铁电极化可以改变自身的自旋织构。基于密度泛函理论计算,我们发现可以通过铁电极化可以进一步调节自旋霍尔电导(spinHallconductivity,简记为SHC),通过计算得到自旋霍尔电导的一个分量σxyz在带边缘附近可以达到100?/e(?cm)-1的量级,其主要原因在于电极化改变了能带结构。该研究工作为可控的自旋输运的实验和理论研究具有重要的价值,必将推动自旋电子学的进一步发展。     

紫金山东南矿段成矿期次、阶段浅析

通过对紫金山东南矿段铜钼(金)矿床地质矿化特征分析,指出铜钼矿化带主要赋存于花岗闪长斑岩的内外接触带,处于似斑状花岗闪长斑岩的上部,金矿化带赋存在表生氧化带的英安玢岩、隐爆角砾岩中。经过对矿石的组构特征、矿物生成顺序等特征分析,将矿床的成矿演化过程分为斑岩热液期、高硫化浅成低温热液期、表生氧化期三个主要矿化期次,进一步将斑岩热液期分为黑云母-钾长石化阶段、石英-绢云母化阶段、碳酸盐化阶段三个阶段;高硫化浅成低温热液期分为地开石化阶段、明矾石化阶段、硅化阶段三个阶段。研究结果为进一步研究矿床成因提供了依据。     

水平衡法与高温转化法在矿泉水氢氧稳定同位素测定中的应用

为了鉴别不同品牌矿泉水标注水源地信息真伪,对11种不同品牌饮用水的氢氧稳定同位素(δD和δ18 O)进行测定。结果表明,水平衡法(GasBench-IRMS)和高温转化法(TC/EA-IRMS)的测定结果一致性较好,两种方法测定6种不同饮用水的δD和δ18 O的平均差异分别为(0.6±1.59)‰和(0.02±0.13)‰。水平衡法需要较长的制备和测定时间,但δD和δ18 O的测定精度明显优于高温转化法。11种饮用水δD和δ18 O变化范围较大,其δD和δ18 O受不同品牌饮用水的水源地降水影响形成明显的地域性。虽然无法区分矿泉水是否由其他类别饮用水伪造,但δD和δ18 O可以为特定区域(如高海拔与沿海地区)以及产地相近的矿泉水水源地鉴别提供依据。